How to Measure Your Kitchen Before Ordering Cabinets
Measure every wall from corner to corner in inches, then locate each window, door, pipe, gas line and outlet by its distance from the nearest corner and its height off the floor. Add the ceiling height in several spots, the size of every appliance you plan to keep or buy, and a check of whether the corners are square. That set of numbers is enough for a designer to lay out cabinets and price them. One rule runs through all of it. When two readings of the same wall disagree, the cabinets have to fit the smaller one.
Your own measurements get a quote and a first layout started. They do not have to be perfect, because a cabinet order should be placed from dimensions a designer has verified in the room.
What to have on hand
Use a steel tape measure long enough to span your longest wall in one pull, a pencil, plain or graph paper, a level (a longer one reads walls and floors more accurately than a short one) and your phone camera. A second person helps on long walls, because a tape that sags in the middle reads long. Write every figure in inches with the fraction shown on the tape. Rounding to the nearest inch is how a filler strip ends up too narrow.
Step 1: Sketch the room from above
Draw the room as if the roof were off. Label the walls A, B, C and so on, moving clockwise from the doorway you use most. Mark windows, doors, pass-throughs and any wall that stops short. The sketch does not need to be to scale. Its job is to hold numbers in the right places, so leave plenty of white space around each wall.
Step 2: Measure each wall more than once
Run the tape from corner to corner at countertop height, then again near the floor and again near the ceiling. In real houses walls lean and bow, so the readings rarely match. Record all of them and circle the smallest. Measure from finished wall surface to finished wall surface, never from baseboard to baseboard, since cabinets sit against the wall and the baseboard comes off behind them. If tile or wainscoting covers part of a wall, note how thick it is and where it stops.
Step 3: Locate windows and doors
For each opening, take three horizontal numbers: from the corner to the outside edge of the trim, the width of the opening including trim on both sides, and from the far edge of the trim to the next corner. Those three should add up to the wall length from Step 2. If they do not, one of them is wrong, and it is faster to find out now.
Then measure up from the floor to the bottom of the window sill and to the top of the trim. The sill height decides whether a countertop and backsplash can pass under the window, and the top of the trim limits what can hang beside it. For doors, note which way each one swings and how much wall the open door covers.
Step 4: Ceiling height, soffits and beams
Measure floor to ceiling in every corner and at the middle of each cabinet wall. Floors slope and ceilings sag, so the lowest reading is the one that limits how tall the wall cabinets and crown molding can be. Our guide to choosing between 30-, 36- and 42-inch wall cabinets shows how that number turns into a cabinet height.
A soffit is the boxed-in section above many older cabinet runs. Record how far it drops from the ceiling, how far it projects from the wall and how long it runs. If you know what is inside, write that down too. An empty soffit can often be removed by a contractor before the cabinets arrive. One that hides a duct or a drain stays unless someone reroutes what is in it, and the layout has to work beneath it.
Step 5: Plumbing, gas, electrical and vents
Utilities decide where the sink base and the range go, unless you hire a licensed plumber or electrician to move them. For each item below, record the distance from the nearest corner to its center and its height off the floor:
- Sink drain and the hot and cold supply lines
- Gas line and its shutoff valve
- The range receptacle, plus every wall outlet and switch on a cabinet wall
- The hood duct, if the current hood vents outside
- Heat registers, baseboard heaters and radiators
- Anything else a cabinet cannot cover, such as an electrical panel, a thermostat or an access hatch
Photograph each one with the tape in the frame. A designer can read a photo faster than a description.
Step 6: Appliance sizes
Cabinets are built around appliance openings, so guesses here cost more than guesses anywhere else. For appliances you are keeping, measure the unit itself. For new ones, pull the installation guide by model number and copy the cutout dimensions the manufacturer lists.
| Appliance | What to record | Why it matters |
|---|---|---|
| Refrigerator | Width, height, depth with doors and handles, hinge side | Sets the opening and how far the unit stands past the counter |
| Range or cooktop | Width, fuel, freestanding or slide-in | Fixes the gap between base cabinets and the hood size above |
| Dishwasher | Width and height | Needs its own opening beside the sink base |
| Sink | Bowl width, front-to-back size, mount type | Determines the sink base cabinet width |
| Hood or microwave | Width, ducted or recirculating | Changes the wall cabinet above the range |
Step 7: Check for square, plumb and level
To test a corner, mark a point 3 feet out along one wall and 4 feet out along the other, then measure the diagonal between the marks. Exactly 5 feet means the corner is square. A shorter diagonal means the corner is tighter than a right angle, and a longer one means it is open. Next, hold the level upright against each cabinet wall, then lay it on the floor along the same wall, and note which end is high.
You are not expected to fix any of this. The designer needs to know about it, because an out-of-square corner uses up filler space and a sloping floor changes how the base cabinets are shimmed. Houses with a few decades behind them tend to have more of both, which is covered in our article on fitting new cabinets into an older house.
Mistakes that throw off a layout
- Measuring the old cabinets instead of the walls. Old cabinets tell you what someone installed, and the room may allow more or less.
- Leaving out the trim. A window with wide casing takes more wall than the glass suggests.
- Recording one ceiling height for the whole room.
- Forgetting the door swing, then drawing a pantry where the door opens.
- Skipping the refrigerator depth, which decides whether it blocks a walkway or a neighboring drawer.
From tape measure to a priced layout
Once the sketch is filled in, photograph it along with each wall and send it through the Aqua Kitchen contact page for a quote based on your numbers. Before anything is ordered, book the free 3D kitchen design service, in which a designer measures the room, builds a 3D model of your layout and revises it with you, with no obligation to buy. While you wait, you can browse the kitchen cabinet lines the showroom carries and read how a 10 x 10 kitchen is priced, since your wall lengths show how far your room is from that standard footprint. If you are visiting in person, our list of what to bring to a showroom appointment covers the rest.
