Planning Kitchen Lighting Before Finalizing Cabinet Placement
Make the kitchen lighting plan while the cabinet layout is still a drawing. The positions of under-cabinet lights, recessed fixtures and island pendants all depend on where the cabinets end up, and the wiring for them goes into the walls and ceiling before a single cabinet is hung. Lighting chosen after installation is limited to whatever can be fished through finished walls.
Why lighting belongs on the cabinet drawing
Cabinets affect lighting in three ways. They set where the counters are, and counters are what task lighting has to reach. They hide fixtures and wires, through light rail molding, valances and the space above the boxes. And they block light, because a wall cabinet shades the counter below it and crown molding or a tall pantry can cut into the beam of a ceiling fixture.
The NKBA Kitchen Planning Guidelines state the goal plainly: in addition to the general lighting that code requires, every work surface should be well illuminated by appropriate task lighting. You cannot check that until you know where every work surface and every wall cabinet will be.
Under-cabinet lighting and light rail molding
Ceiling lights sit behind a person standing at the counter, so the person's own body shades the work. A U.S. Department of Energy guideline on residential lighting makes the point directly, noting that under-cabinet lights prevent shadows from a person working at the counter. That makes them the first fixtures to plan, and the ones most tied to cabinet details.
The molding
Light rail molding is a strip fixed along the bottom front edge of the wall cabinets. It hides the fixture from view and keeps the light source out of the eyes of anyone seated at a table or island nearby. It is ordered with the cabinets in the same finish. Adding it later means matching a finish after the fact, so decide on under-cabinet lighting before the cabinet order goes in, even if the fixtures themselves come later.
The cabinet bottom
Some wall cabinets have a recessed bottom that conceals a slim fixture without help. Others have a flush bottom, which leaves the fixture exposed unless a light rail covers it. This differs by cabinet line and door overlay, so ask how the underside of the wall cabinets is built on the line you are choosing.
Fixture position and the countertop
Mount the fixture toward the front of the cabinet so the light lands on the part of the counter where you work. A fixture at the back lights the backsplash and, on polished stone, shows up as a row of bright reflections in the countertop. A continuous diffused strip reflects as a soft band, which is easier to live with on a glossy surface than separate points.
The wire
Each run of under-cabinet lights needs a feed wire that comes out of the wall where the cabinet will hide it, and a place for the driver or transformer if the system uses one. Both are set at rough-in, before drywall is closed. With a slab backsplash the stakes are higher, because openings for switches and receptacles are cut in the fabrication shop. See our guide to full-height stone backsplashes for how those cutouts are planned.
Recessed lights and the counter edge
The same Department of Energy guideline gives a clear rule for recessed lights in a kitchen: position the downlights directly above the front edge of the countertop, which lights the counter well and puts light into the cabinet interiors. Add other fixtures for general room light after those are placed.
Translate that into cabinet dimensions. The KCMA cabinet standard lists 24 inches as the typical depth of a base cabinet and 12 inches for a wall cabinet. The counter's front edge is therefore about a foot in front of the wall cabinet doors, and that is where the row of fixtures belongs. A grid centered on the room, laid out before the cabinets are drawn, tends to put the lights over the aisle and the cook's shadow on the cutting board.
Two cabinet details can spoil a correct layout. Crown molding projects beyond the cabinet face, and a fixture too close to it throws a hard scallop of light on the molding and loses part of its beam. Tall cabinets and refrigerator panels stand deeper than wall cabinets and can block a fixture placed beside them. The electrician needs the cabinet elevations, with crown projection and tall cabinet depths marked, to avoid both. In a room with limited headroom the fixture choice narrows further, as our guide to cabinet design under a low ceiling explains.
Pendants over an island or peninsula
Pendants are centered on the island, and the island is wherever the cabinet plan puts it. The ceiling boxes for pendants are set at rough-in, well before the island is installed. If the island grows by a cabinet or shifts to widen an aisle after that, the pendants end up off center and the fix is a ceiling patch.
Lock the island's length, width and position before the electrician marks the ceiling. Then settle three things from the drawing: how many pendants the length can carry without crowding, whether they clear the sight line between someone standing at the island and someone seated across from it, and whether an island range hood competes for the same space. Follow the fixture maker's instructions for hanging height. The Department of Energy guideline notes that pendants can take the place of recessed downlights over a peninsula or freestanding counter, so the two do not need to be doubled up.
The island's receptacles and any appliance circuits are decided at the same stage. Our article on island electrical planning covers what to coordinate.
Lighting inside, above and below the cabinets
Glass-door cabinets with interior lights need a wire path into the box and a finished interior worth lighting. Tell the designer which cabinets will be lit so they can be ordered accordingly.
Light above the wall cabinets depends on a gap. The Department of Energy guideline describes cove lighting as workable when wall cabinets are mounted with 10 to 12 inches or more of space to the ceiling. That makes the choice between cabinets that run to the ceiling and cove lighting above them a single decision, to be made when cabinet heights are picked.
Toe-kick lighting gives a low path light at night. Its feed has to be at floor level before the base cabinets are set. For the flat-panel kitchens these details usually go with, see our overview of modern kitchen designs.
What has to be in place before the cabinets hang
- The electrician has the final cabinet elevations, showing wall cabinet heights, light rail, crown and tall cabinets.
- Feed wires for under-cabinet lights are stubbed out where each cabinet run will conceal them.
- Recessed housings are located from the future counter edge, not from the room's centerline.
- Pendant boxes are centered on the island or peninsula as drawn.
- Switches and dimmers are placed clear of tall cabinets, door casings and the end of the backsplash, with each layer of light on its own control. The NKBA access standard recommends lighting from multiple sources that is adjustable.
- The rough electrical inspection is passed before the walls are closed.
Cabinets, countertop template and backsplash follow in that order. The cabinet installation checklist lists what else should be ready on the day.
Who does what
Wiring, fixtures and switches are the work of a licensed electrician. In New Jersey, new wiring of this kind generally needs a construction permit under the state's Uniform Construction Code. Your municipal construction office decides what your job requires and handles the permit and inspections. Our guide to permits for a New Jersey kitchen remodel has the details.
Aqua Kitchen does not do electrical work. We design the cabinet layout and supply and install the cabinets, including light rail and crown molding ordered with them. Ask the designer what drawings or dimensions from that design you can pass to your electrician.
Put the lights on the cabinet drawing
When you use our free 3D design and measuring service, ask the designer to show the light rail, the crown projection and the island centerline in the model, and ask for the cabinet dimensions your electrician needs before rough-in. Light rail and crown profiles differ by line, so check which moldings come with the kitchen cabinets you are considering.
