How to Keep a Kitchen Backsplash Clean and Maintain Grout
Wipe a kitchen backsplash with warm water and a little dish soap while the splatter is fresh, rinse it, and the tile or stone face stays clean with little effort. The parts that need real maintenance are the grout, which is porous and holds stains, and the bead of caulk where the backsplash meets the countertop, which needs replacing sooner than the grout or the tile. Each needs a different cleaner and a different repair.
The tile face needs the least work
Glazed ceramic and porcelain tile release dirt easily. The Tile Council of North America (TCNA) says tile can often be cleaned with water alone, and that clean tile tends to stay clean because it does not hold a static charge that attracts dust. What undoes that is residue. According to TCNA, a cleaner that is not rinsed off leaves a sticky soap film, and the film is what collects dirt. So the weekly wipe-down is a mild cleaner, a rinse with clean water and a dry cloth.
Removing grease behind the range
Cooking oil leaves the pan as a fine mist, settles on the wall and, left alone, turns tacky and traps dust. Soap and water stop working at that point. Grease is cut by an alkaline cleaner, which is also the type TCNA recommends for grout, so one product handles both the tile and the joints.
- Mix an all-purpose alkaline household cleaner with warm water as the label directs.
- Wet the wall with it and give it time to soften the film before you scrub.
- Work the grout lines with a soft nylon brush and wipe the tile faces with a cloth or sponge.
- Rinse with clean water, changing the water as it clouds. Rinse a second time if the wall still feels slick.
- Dry the surface so no cleaner is left to dry in the joints.
Stay away from oil soaps and wax-based or pine oil cleaners on a tiled wall. TCNA warns that grout absorbs them and is left with a waxy or oily film, which is the opposite of what you want behind a range.
Why grout stains, and what to clean it with
Standard grout is cement and sand. TCNA describes it as porous, with enough microscopic surface area to soak up a stain the way fabric does. The sand is chemically tough. The cement is alkaline and dissolves in acid.
That chemistry rules out the most common home remedy. Vinegar reacts with grout the way it reacts with baking soda, in TCNA's comparison, so a vinegar scrub lifts the stain by removing a little of the joint each time. The council's answer on how to clean grout recommends alkaline cleaners instead, and mentions enzyme cleaners made for tile and grout as another option. For a stain that survives both, it suggests pressurized steam. Cutting the grout out and regrouting is the last resort, and it has to be done without loosening the tile.
Epoxy grout is a different material. TCNA calls it virtually as stain-proof as the tile, and it is not sealed. If your backsplash has it, the cleaning advice for the tile face covers the joints too.
Sealing cement grout
TCNA recommends sealing cement grout and describes two kinds of sealer. A penetrating sealer bonds inside the grout and repels water and water-based stains without coating the joint. It costs more and lasts longer, and some versions also repel oil. A topical sealer coats the surface. It blocks nearly everything until it wears, costs less, and gives the joint a plastic look.
Behind a range, the stains are oil-based, so a penetrating sealer rated for oil is the one that matches the exposure. New grout has to cure before any sealer goes on, and sealers wear at different rates. The sealer manufacturer's label sets both the waiting time and the reapplication schedule.
Stone backsplashes: the 4-inch splash and the full-height slab
A stone backsplash cut from the countertop slab has no grout. Clean it with whatever the countertop takes, since it is the same material. Our guide to cleaning countertops by material lists what quartz, granite, marble and porcelain makers allow and forbid.
Three things are different on a wall. Splatter dries where it lands instead of pooling, so a weekly wipe matters more than it does on the counter. A polished slab sits at eye level and shows streaks, so finish with a dry cloth. And a marble backsplash behind the range is exposed to acidic splatter. According to the Natural Stone Institute, acids as ordinary as lemon juice and vinegar dull or etch calcareous stones, and marble is one of them. The institute also cautions that scouring powders and creams can scratch stone. Natural stone tile, such as a marble mosaic, has both problems, grout that stains and a surface that reacts to acid. Use a neutral cleaner on it and keep the acids away.
If you are weighing grout against a slab for a kitchen that is still being planned, the comparison of tile and stone slab backsplashes covers cost and design, and the article on full-height stone backsplashes covers how a slab wall is measured and installed.
The caulk joint where the backsplash meets the countertop
The line at the bottom of the backsplash is filled with flexible caulk, and for a reason. TCNA's guidance on when to use caulk instead of grout explains that surfaces on different backings move independently, and that grout in such a joint cracks and lets moisture through. The countertop and the wall are exactly that case.
The same guidance is frank about the cost. Caulk needs more maintenance than grout, mold grows on it more easily unless it contains a mildewcide, and its color ages differently from the grout beside it. TCNA also notes that acrylic caulk breaks down in wet horizontal joints and that silicone or urethane holds up better.
Day to day, the joint needs two things. Wipe it dry after washing dishes, because standing water behind the faucet is what feeds mold. And clean it with soapy water and a cloth, never a stiff brush or a scraper that can tear the bead.
Replace the caulk when it has pulled away from the stone or the tile, when it has cracked, or when dark staining no longer washes off. Cut the old bead out completely, let the joint dry, and run a new bead of kitchen and bath silicone. Behind a sink this is more than cosmetic. An open joint lets water run down behind the countertop toward the cabinet box, which is the subject of our guide to protecting cabinets from moisture at the sink and dishwasher. If the joint was grouted and has cracked, rake the grout out and caulk it, because new grout in that joint will crack the same way.
Backsplash and grout questions
What is the white haze or powder on the grout?
Two causes are common. Soap residue comes off with repeated clean-water rinses and some brushing. Efflorescence is mineral salt carried to the surface by moisture, and TCNA notes that it is generally removed with acid, which also attacks the cement in the grout. That makes it a job for an experienced professional, and a reason to find out where the moisture is coming from.
Can new grout go over stained grout?
Generally no. TCNA says the old grout has to be cut out first, because the contamination that discolored it can keep new grout from bonding.
Should the tile itself be sealed?
Glazed tile should not be. TCNA's view is that the glaze is easier to clean and longer lasting than any coating. Unglazed tile generally is sealed, following the tile manufacturer's instructions. Natural stone tile is commonly treated with an impregnating sealer, which the Natural Stone Institute describes as a repellent that slows staining and does not make the stone stain proof.
If the backsplash is not chosen yet
Cleaning belongs in the decision. A backsplash cut from the same slab as the counter removes grout from the wall, and it is decided along with the countertop, before fabrication. You can look through the quartz, granite and marble we cut in our Wayne shop to see which materials you would want on a wall, and if tile is the plan, our article on pairing a backsplash with granite helps with color before you commit to a grout.
